Best Blu-ray Movie Deals

Best Blu-ray Deals, Cheap Blu-ray Movies!
Top deals | Price drops  
 All countries United States United Kingdom Canada Germany France Spain Italy Japan
The Revenant (Blu-ray)
Central Intelligence (Blu-ray)
The Secret Life of Pets 3D (Blu-ray)
Gremlins Collection (Blu-ray)
Ash vs Evil Dead: The Complete First Season (Blu-ray)
Star Trek Beyond (Blu-ray)
The Witch (Blu-ray)
Star Trek: The Original Series - The Roddenberry Vault (Blu-ray)
Hammer Horror 8-Film Collection (Blu-ray)
Santana IV - Live at The House of Blues, Las Vegas (Blu-ray)
Daredevil: The Complete First Season (Blu-ray)
Trilogía de Guillermo del Toro (Blu-ray)
What's your next favorite movie?
Join our movie community to find out

Image from: Life of Pi (2012)

Go Back   Blu-ray Forum

guitarist155 guitarist155 is offline

Special Member

Community profile

Visitor Messages

Showing Visitor Messages 1 to 5 of 5
  1. guitarist155
    07-24-2011 07:41 PM
    If you are talking about the ones hanging in front of the receiver, they are the temporary IR emitters for the remote until the stuff for hardwiring the IR control comes. As the system is in an equipment room and not in the theater.
  2. vabney84
    07-24-2011 07:25 PM
    hey nice setup but i have a ? what are those cables that got that red end thats coming from your receiver
  3. Bluvette
    07-23-2011 09:52 PM
    Thanks for the feedback.I have a Denon 3311 and with Audyssey set my subs run @ +2 db. So I dialed up the receiver to +7 db and lowered my gain on my subs and reset them to 75dbs on the slp meter using the gain on the subs. Now the transducer is hitting pretty good may have to dial it down on the Dayton amp. For the hell of it I ordered this plate amp I got it for $109 shipped. I am going to install it into a MDF box I will build. What do you think?? Thanks again.


  4. Bluvette
    07-23-2011 08:07 PM
    Thanks for the reply. The picture you see is how I had the transducer mounted originally, which was mounted to the seat frame. I contacted Parts Express where I purchased it and the tech said to take it off the frame and move it to the seat springs (the ones the cushion sets on right under my butt). So what I did was to cut the wood down a bit smaller and attached the transducer back to it, drilled holes into the wood then ziptied the wood with the transducer to the seat springs. As for the amp it's 150w total 75 per channel, I am only using one channel so 75 watts. I was also thinking the same thing about the receiver setting for the sub, so I will check on that. Also I do have about a 1/2 of inch between the transducer and wood. Thanks again for the help.

  5. Mr. Joshua
    06-08-2010 03:47 AM
    Mr. Joshua
    Like your home theater setup cool system!

About Me

  • About guitarist155
    evil electronics genious and audio engineer. I play many instruments but am most skilled in guitar
    home automation, computers, industrial automation control system design, recording studio design.
  • Signature
    This signature will be updated soon! ps3 games: 5 blu-ray: 57
    psn: guitarist155

    projector: Epson 8345 Processors:onkyo tx-nr809 and UMC-200 for bedroom sources:120g PS3 slim, AMPS: power: , APC H10 speakers: Niles pro LCR and di/bipole surround back with 8in carbon in ceiling for sides. Polk CS2 center, monitor 60 fronts, 2 x psw10 subwoofers. (for bedroom) remote Harmony 890 (RF ;) ) Screen: HDVio 110" electric.


Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: 05-15-2016 07:14 PM
  • Member since: 01-10-2008
  • Referrals: 0


Showing Friends 1 to 6 of 6

Member Profile Recent Ratings Contact Info
Feedback Score:
Positive Feedback:
Members who left positive:
Members who left negative:
Total positive feedback: 1
Submit Feedback For guitarist155
6 Months
12 Months
Positive Positive 0 0 0
Neutral Neutral 0 0 0
Negative Negative 0 0 0
Member since:
Last Activity:  

All times are GMT. The time now is 03:36 PM.