No HDMI question - Blu-ray Forum

Vanwolfenstein · 01-13-2008, 02:04 AM

I just purchased the Panny 30 and the Onyko 605. I have a cable box that has HDMI. I have a Kuro on order. In the meantime, I am attempting to configure my system.

My HDTV has no HDMI input. I am using component from the receiver.

Here is the question.

I am trying to connect the Cable box and the Panny via HDMI to the receiver. No luck, no picture/no sound. Do I have to complete the "circuit" with the HDMI tv? Is using the component out to the TV somehow not allowing me to connect the cablebox and Panny using HDMI?

On the receiver I have (I believe) made the changes needed on setup so the receiver knows that I am connected for HDMI. The component setup works fine.

Ken

fattyslimslim · 01-13-2008, 02:18 AM

You are correct. Do you still have your 605 manual? Check page 24, 25, the 605 does not support the signal flow of HDMI-in-> Component-out. If you want to use the HDMI-inputs, you need to use the HDMI outputs.
Until you get your HDMI tv, you will need to use inputs other than HDMI.

Vanwolfenstein · 01-13-2008, 03:14 AM

Thank you for your response....whew....I'm not crazy

Ken

01-13-2008, 02:04 AM	#1
Vanwolfenstein Junior Member Member since:Dec 2007	No HDMI question I just purchased the Panny 30 and the Onyko 605. I have a cable box that has HDMI. I have a Kuro on order. In the meantime, I am attempting to configure my system. My HDTV has no HDMI input. I am using component from the receiver. Here is the question. I am trying to connect the Cable box and the Panny via HDMI to the receiver. No luck, no picture/no sound. Do I have to complete the "circuit" with the HDMI tv? Is using the component out to the TV somehow not allowing me to connect the cablebox and Panny using HDMI? On the receiver I have (I believe) made the changes needed on setup so the receiver knows that I am connected for HDMI. The component setup works fine. Ken Last edited by Vanwolfenstein; 01-13-2008 at 02:08 AM.

01-13-2008, 03:14 AM	#3
Vanwolfenstein Junior Member Member since:Dec 2007	Thank you for your response....whew....I'm not crazy Ken Last edited by Vanwolfenstein; 01-13-2008 at 04:14 AM.

Similar Threads
thread	Forum	Thread Starter	Replies	Last Post
PQ question--my first HDMI TV	General Chat	JimShaw	2	05-18-2009 03:57 AM
HDMI Through Question	Receivers	poogie	9	03-29-2009 12:19 AM
HDMI question	Newbie Discussion	pauldec	7	10-15-2008 05:57 AM
HDMI 1.1 question...	Home Theater General Discussion	tuco87	2	10-09-2008 07:43 PM
question about speaker wire/hdmi vs non hdmi audio	Speakers	Erman_94	13	05-21-2008 03:19 PM

01-13-2008, 02:18 AM	#2
fattyslimslim Active Member Member since:Aug 2007 Location:Little Frisco, WI Blu-ray collection:181 Trading Score:2	You are correct. Do you still have your 605 manual? Check page 24, 25, the 605 does not support the signal flow of HDMI-in-> Component-out. If you want to use the HDMI-inputs, you need to use the HDMI outputs. Until you get your HDMI tv, you will need to use inputs other than HDMI.

Best Blu-ray Movie Deals