Clip-on intercooler for PS3 - Blu-ray Forum

SundayDuffer · 03-14-2007, 06:19 PM

I have been using a small fan for my PS3..that seemed to help with the freezing/pausing problem. Now that Nyko is coming with this intercooler attachment...I think i will pick one up as soon as it hits the market.

http://www.nyko.com/nyko/products/?i=93

Thanos417 · 03-14-2007, 06:23 PM

It was suppose to hit the market in January, but has been delayed several times, the latest release date is April 15th, so we will see....

dialog_gvf · 03-14-2007, 06:26 PM

Interesting. The PS/3 outputs air on the right side/top and this is attached to the rear of the unit. So, is it an air PUSHER?

Gary

SundayDuffer · 03-14-2007, 07:09 PM

Quote:

Originally Posted by dialog_gvf

Interesting. The PS/3 outputs air on the right side/top and this is attached to the rear of the unit. So, is it an air PUSHER?

Gary

If you open up the PDF on the site...a bigger image is there. This cooler looks like a tray..the whole PS3 will just fit tightly inside this cooler. 5 fans with customized speed control? That is cool.

dialog_gvf · 03-14-2007, 07:15 PM

Quote:

Originally Posted by SundayDuffer

If you open up the PDF on the site...a bigger image is there. This cooler looks like a tray..the whole PS3 will just fit tightly inside this cooler. 5 fans with customized speed control? That is cool.

Yes, you're right. It goes over the right/top outlet too. It's such a clean fit it wasn't obvious from the small pic.

It does look cool. I wonder how quiet it would be, and whether it would only push a lot when it needs to.

Gary

Gremal · 03-14-2007, 07:26 PM

If you scroll to the bottom of that PDF, it refers to a single, inner and master version with 1, 5 and 20 fans, respectively. The 5-fan version weighs almost 9 lbs and the 20-fan version weighs almost 40 lbs! This will significantly change the PS3...or am I reading the PDF wrong.

Gremal · 03-14-2007, 06:49 PM

Quote:

Originally Posted by SundayDuffer

I have been using a small fan for my PS3..that seemed to help with the freezing/pausing problem. Now that Nyko is coming with this intercooler attachment...I think i will pick one up as soon as it hits the market.

http://www.nyko.com/nyko/products/?i=93

Thanks for the heads-up. I have noticed the PS3 runs very hot. Haven't experienced any freezing/pausing problems, but with record high temps here and summer just around the corner I will definitely pick up one of these attachments. Hope it is available soon.

Amon37 · 03-14-2007, 08:04 PM

It's always 76 to 78 degrees in my house during the summer so high temps outside don't factor at all for me. My PS3 is never overheating, I feel hot air blowing out of the fan which is normal.

SundayDuffer · 03-14-2007, 08:40 PM

Mine was runninng pretty hot til i put a small fan next to it.

Anyhow...i looked it up...the Nyko will run $29.99.
And i have also found another version of cooler for the PS3 made by Pelican...couldn't find any specs on it, but GameStop will have it in tomorrow for $39.99.

http://www.gamestop.com/product.asp?...ct%5Fid=802609

Blackraven · 03-15-2007, 08:12 AM

The shift to 65nm process for the hardware components is by itself already enough to reduce heat and noise.

This fan is not needed at all (unless you own a PS3 that has 90nm parts in it)

Gremal · 03-15-2007, 05:02 PM

How do you know what size your parts are?

shido · 03-15-2007, 05:57 PM

Quote:

Originally Posted by Blackraven

The shift to 65nm process for the hardware components is by itself already enough to reduce heat and noise.

This fan is not needed at all (unless you own a PS3 that has 90nm parts in it)

Do you mean 360? I haven't heard anything about the PS3 changing specs like that, but the 360 supposedly is.

movies3 · 03-15-2007, 08:36 PM

Quote:

Originally Posted by Amon37

It's always 76 to 78 degrees in my house during the summer so high temps outside don't factor at all for me. My PS3 is never overheating, I feel hot air blowing out of the fan which is normal.

yes same with me, my ps3 never gets hot at all.

Gamekid · 03-15-2007, 09:07 PM

Not to offend anyone that uses a cooling fan, but how can you run into heating problems. Unless you block the vents, I don't see how you can have a heating problem.

takezo · 03-16-2007, 08:20 PM

Quote:

Originally Posted by SundayDuffer

I have been using a small fan for my PS3..that seemed to help with the freezing/pausing problem. Now that Nyko is coming with this intercooler attachment...I think i will pick one up as soon as it hits the market.

http://www.nyko.com/nyko/products/?i=93

Seems to help is just another way of saying that it still freezes but somehow not as much, due to me making it cooler. It's all in your mind.

First make sure have updated to the lates firmware.

If pausing happens in Bluray, then it's your nework adapter. Disable internet connection and B-ray movies will run fine. Hopefully this issue is resolved in the next update firmware.

If PS3 realy does freeze due to temperature, the red power light will blink. It's an error code listed in the manual of the PS3 to indicate overheating.
Basicaly if it don't blink, it did not overheat. And the Nyko fan is usless, waste of money, totaly designed for paranoid.

If games freeze, it could be a number of things.

If your playing PS1 or PS2 games, some games may not work %100 flawless.

Disks maybe dirty or scratched.

PS3 demos can lock up due to unrefined code, which is expected in prereleased software.

PS3 it's self can be defective if constant freezing and locking up ocurr.

----------------------------------------------------------------
I know from experience that adding more case fans to a PC will not improve cooling very much. It just make your system very noisey.

The same with PS3, or Xbox 360.

SundayDuffer · 03-16-2007, 09:20 PM

you know what...if i can pick up a coolpad for $10-$20..sure, i'd buy it and put it underneath the PS3...and just leave it there. I might be one of those unlucky guy that got a HOT ps3...besides the pausings here and there, much less now with the latest firmware (maybe 1-2 pauses in 5 movies), the PS3 is still ok..and i am enjoying it.

thanks for all the inputs guys.

03-14-2007, 06:19 PM	#1
SundayDuffer Member Member since:Jan 2007 Location:San Jose, CA	Clip-on intercooler for PS3 I have been using a small fan for my PS3..that seemed to help with the freezing/pausing problem. Now that Nyko is coming with this intercooler attachment...I think i will pick one up as soon as it hits the market. http://www.nyko.com/nyko/products/?i=93

Similar Threads
thread	Forum	Thread Starter	Replies	Last Post
PS3 Intercooler	PS3	jamclaur	20	09-23-2008 09:16 PM
Intercooler for PS3?	Blu-ray Players and Recorders	disbthai	13	07-12-2007 08:32 PM
Questions about Intercooler for PS3	PS3	bferr1	3	06-07-2007 03:13 PM
PS3 intercooler	PS3	movies3	6	05-18-2007 12:50 AM

03-14-2007, 06:23 PM	#2
Thanos417 Active Member Member since:Jan 2007 Location:Glenside, PA Blu-ray collection:10 Trading Score:13	It was suppose to hit the market in January, but has been delayed several times, the latest release date is April 15th, so we will see....

03-14-2007, 06:26 PM	#3
dialog_gvf Moderator Member since:Nov 2006 Location:Toronto Blu-ray collection:320	Interesting. The PS/3 outputs air on the right side/top and this is attached to the rear of the unit. So, is it an air PUSHER? Gary

03-14-2007, 07:26 PM	#6
Gremal Blu-ray Samurai Top ranked HT gallery Member since:Feb 2007 Location:Daddyland Home Theater Gallery:49 Blu-ray collection:184	If you scroll to the bottom of that PDF, it refers to a single, inner and master version with 1, 5 and 20 fans, respectively. The 5-fan version weighs almost 9 lbs and the 20-fan version weighs almost 40 lbs! This will significantly change the PS3...or am I reading the PDF wrong.

03-14-2007, 08:04 PM	#8
Amon37 Power Member Member since:Jan 2007 Location:USA,Arizona PSNetwork: Amon37	It's always 76 to 78 degrees in my house during the summer so high temps outside don't factor at all for me. My PS3 is never overheating, I feel hot air blowing out of the fan which is normal.

03-14-2007, 08:40 PM	#9
SundayDuffer Member Member since:Jan 2007 Location:San Jose, CA	Mine was runninng pretty hot til i put a small fan next to it. Anyhow...i looked it up...the Nyko will run $29.99. And i have also found another version of cooler for the PS3 made by Pelican...couldn't find any specs on it, but GameStop will have it in tomorrow for $39.99. http://www.gamestop.com/product.asp?...ct%5Fid=802609

03-15-2007, 08:12 AM	#10
Blackraven Expert Member Member since:Jan 2005 Location:Makati, Philippines	The shift to 65nm process for the hardware components is by itself already enough to reduce heat and noise. This fan is not needed at all (unless you own a PS3 that has 90nm parts in it)

03-15-2007, 05:02 PM	#11
Gremal Blu-ray Samurai Top ranked HT gallery Member since:Feb 2007 Location:Daddyland Home Theater Gallery:49 Blu-ray collection:184	How do you know what size your parts are?

03-15-2007, 09:07 PM	#14
Gamekid Power Member Member since:Feb 2006	Not to offend anyone that uses a cooling fan, but how can you run into heating problems. Unless you block the vents, I don't see how you can have a heating problem.

03-16-2007, 09:20 PM	#16
SundayDuffer Member Member since:Jan 2007 Location:San Jose, CA	you know what...if i can pick up a coolpad for $10-$20..sure, i'd buy it and put it underneath the PS3...and just leave it there. I might be one of those unlucky guy that got a HOT ps3...besides the pausings here and there, much less now with the latest firmware (maybe 1-2 pauses in 5 movies), the PS3 is still ok..and i am enjoying it. thanks for all the inputs guys.

Best PS3 Game Deals