What type of speaker cable? - Blu-ray Forum

Tempest3991 · 10-22-2009, 02:06 AM

i just bought an Onkyo sr 507 receiver and a pair of polk 40's for the front and a pair of polk 30's for the rear....

Thing is, i'm not certain what type of speaker cable to get. I'm looking at monoprice.com at speaker wire and i'm not sure what to get.

http://www.monoprice.com/products/su...02&cp_id=10239

Theres 12, 14, 16 and 18 gauge i'm assuming.

Also, i bought a polk audio CS2 for my center speaker

Thanks for your help

Tempest3991 · 10-22-2009, 02:13 AM

I just ready the speaker guide and i believe these are 8 ohm speakers because newegg says "Nominal Impedance 8 ohms" for the speakers. So i'm assuming 18 AWG wire because its not that far for the speakers to travel

So 18 gauge wire should be good up to 32 feet away from the receiver with a speaker rated at 8 ohms....

Someone please tell me if i'm reading this correctly

Big Daddy · 10-22-2009, 02:19 AM

Quote:

Originally Posted by Tempest3991

I just ready the speaker guide and i believe these are 8 ohm speakers because newegg says "Nominal Impedance 8 ohms" for the speakers. So i'm assuming 18 AWG wire because its not that far for the speakers to travel

So 18 gauge wire should be good up to 32 feet away from the receiver with a speaker rated at 8 ohms....

Someone please tell me if i'm reading this correctly

The difference in price is so small that you should get 14 gauge just in case you decide to change speakers in the future.

laie_techie · 10-22-2009, 02:28 AM

As always, if you're going to run the wires through the wall, make sure they are CL2 rated.

DiverSpear · 10-22-2009, 12:36 PM

For the life of me I do not understand why people recommend such small wire gauges. The AVR/Amp is a pwr source and the speaker is the load. The smaller gauges have a higher resistance thus creating a higher loss.

Here are the resistances of 18awg through 10awg (per 1000ft, divide by a 1000 to get per foot):
18 7.95 ohms
16 4.99 ohms
14 3.14 ohms
12 1.98 ohms
10 1.24 ohms

I always recommend 12awg at a minimum. I have the numbers all the way through 2000Kcmils(MCM)

10-22-2009, 02:06 AM	#1
Tempest3991 Junior Member Member since:Apr 2009	What type of speaker cable? i just bought an Onkyo sr 507 receiver and a pair of polk 40's for the front and a pair of polk 30's for the rear.... Thing is, i'm not certain what type of speaker cable to get. I'm looking at monoprice.com at speaker wire and i'm not sure what to get. http://www.monoprice.com/products/su...02&cp_id=10239 Theres 12, 14, 16 and 18 gauge i'm assuming. Also, i bought a polk audio CS2 for my center speaker Thanks for your help

Similar Threads
thread	Forum	Thread Starter	Replies	Last Post
Which type of speaker sound match with Pioneer Elite Receiver?	Receivers	mugupo	4	08-19-2009 11:43 PM
Audioquest Speaker Cable - Which side of cable is "red"	Audio Theory and Discussion	whippersnapper	3	04-13-2009 12:44 AM
Difference between the "screw"-type speaker connector, and the "insert"-type?	Receivers	Chordata	8	02-20-2009 07:31 PM
What Type of Cable?	Newbie Discussion	71Makaveli96	6	07-02-2008 06:26 PM
2 pairs of speaker cable to 1 speaker?	Home Theater General Discussion	Phane	1	01-20-2008 02:47 PM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-22-2009, 02:13 AM	#2
Tempest3991 Junior Member Member since:Apr 2009	I just ready the speaker guide and i believe these are 8 ohm speakers because newegg says "Nominal Impedance 8 ohms" for the speakers. So i'm assuming 18 AWG wire because its not that far for the speakers to travel So 18 gauge wire should be good up to 32 feet away from the receiver with a speaker rated at 8 ohms.... Someone please tell me if i'm reading this correctly

10-22-2009, 02:28 AM	#4
laie_techie Active Member Top contributor Member since:May 2009 Location:Happy Valley, Utah Home Theater Gallery:1 Blu-ray collection:270 DVD collection:159 Blu-ray reviews: 1	As always, if you're going to run the wires through the wall, make sure they are CL2 rated.

10-22-2009, 12:36 PM	#5
DiverSpear Active Member Member since:Mar 2008 Location:St. Cloud, Florida Blu-ray collection:154 Trading Score:1	For the life of me I do not understand why people recommend such small wire gauges. The AVR/Amp is a pwr source and the speaker is the load. The smaller gauges have a higher resistance thus creating a higher loss. Here are the resistances of 18awg through 10awg (per 1000ft, divide by a 1000 to get per foot): 18 7.95 ohms 16 4.99 ohms 14 3.14 ohms 12 1.98 ohms 10 1.24 ohms I always recommend 12awg at a minimum. I have the numbers all the way through 2000Kcmils(MCM)

Best Blu-ray Movie Deals