Samsung firmware - Blu-ray Forum

paulca · 05-26-2007, 02:51 PM

I need to know a step by step process to download the firmware update then open it right then burn it to a disc - thanks

krisjan · 05-26-2007, 03:50 PM

Go to the Samsung web site, find the 1200 player and look for the button that says firmware. Click that and then open the pdf file that has all of the buring and loading instructions. While the language is a little stilted, I was able to understand it enough to successfully do this. They recommend NERO burning sofware but you can use any burning sofware that provides a "burn image" option. If you are not able to do this, email me your address and I'll send you my disc and you can update using that.
Mark

RUR · 05-26-2007, 04:54 PM

FWIW, I grabbed the below from a post on AVS and archived it just in case, even though I updated my player via ethernet. I believe that, since this post, the firmware has appeared on the US site as well.

"I downloaded the new firmware from the Canadian site, and it worked fine. A few comments based on this experience:

1. Make sure you print out the firmware installation instructions from the Canadian site. They are separate from the actual firmware.
2. When I burned the new firmware (using image burn) to a CD-R, it showed up with a .RUF extension, not an ISO extension. This is OK.
3. After using the CD to update the firmware on the player, you must go through the entire setup procedure on the player.

It took me about 5-10 minutes to download and burn the firmware to a CD-R. It then took 7-8 minutes to update the firmware on the player. Re-setting up the player took another couple of minutes. You can confirm that you have the new firmware version by following the instructions in the user manual (see page 47)."

Samsung Canadian download site:
http://www.samsung.ca/cgi-bin/naseca...ort_search.jsp

paulca · 05-27-2007, 05:40 PM

I was able to download the firmware and get in into my Samsung bd-p1000 and both Pirates played very well. I also have the PS3 I like their way of updateing better!!! Thanks again

bwillcox · 06-02-2007, 04:42 AM

It is also possible (and easy) to update the firmware on the P1200 directly via the Internet if you have an Ethernet network to plug the player into.

05-26-2007, 02:51 PM	#1
paulca Active Member Member since:Sep 2006	Samsung firmware I need to know a step by step process to download the firmware update then open it right then burn it to a disc - thanks

05-27-2007, 05:40 PM	#4
paulca Active Member Member since:Sep 2006	Thanks for all your help I was able to download the firmware and get in into my Samsung bd-p1000 and both Pirates played very well. I also have the PS3 I like their way of updateing better!!! Thanks again

Similar Threads
thread	Forum	Thread Starter	Replies	Last Post
new Samsung 2.02 firmware available	Blu-ray Players and Recorders	rowuncw	2	09-03-2009 05:11 PM
need help with samsung firmware update <samsung costumer service no help>	Blu-ray Players and Recorders	ndirtdigler69	1	06-10-2007 05:24 PM
Samsung Firmware 1.1 ?	Blu-ray Players and Recorders	hhansard	10	02-27-2007 01:36 PM
Samsung firmware 1.0 HERE!!!!	Blu-ray Players and Recorders	shamus	41	11-06-2006 04:35 PM
Samsung firmware is here!!!!!!!!	Blu-ray Players and Recorders	shamus	29	10-13-2006 04:34 PM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-26-2007, 03:50 PM	#2
krisjan Active Member Member since:May 2007 Location:Chicago suburbs	Go to the Samsung web site, find the 1200 player and look for the button that says firmware. Click that and then open the pdf file that has all of the buring and loading instructions. While the language is a little stilted, I was able to understand it enough to successfully do this. They recommend NERO burning sofware but you can use any burning sofware that provides a "burn image" option. If you are not able to do this, email me your address and I'll send you my disc and you can update using that. Mark

05-26-2007, 04:54 PM	#3
RUR Blu-ray Guru Member since:Feb 2007 Location:Abiit, excessit, evasit, erupit Blu-ray collection:143 Trading Score:1	FWIW, I grabbed the below from a post on AVS and archived it just in case, even though I updated my player via ethernet. I believe that, since this post, the firmware has appeared on the US site as well. "I downloaded the new firmware from the Canadian site, and it worked fine. A few comments based on this experience: 1. Make sure you print out the firmware installation instructions from the Canadian site. They are separate from the actual firmware. 2. When I burned the new firmware (using image burn) to a CD-R, it showed up with a .RUF extension, not an ISO extension. This is OK. 3. After using the CD to update the firmware on the player, you must go through the entire setup procedure on the player. It took me about 5-10 minutes to download and burn the firmware to a CD-R. It then took 7-8 minutes to update the firmware on the player. Re-setting up the player took another couple of minutes. You can confirm that you have the new firmware version by following the instructions in the user manual (see page 47)." Samsung Canadian download site: http://www.samsung.ca/cgi-bin/naseca...ort_search.jsp

06-02-2007, 04:42 AM	#5
bwillcox Member Member since:May 2007 Blu-ray collection:1	It is also possible (and easy) to update the firmware on the P1200 directly via the Internet if you have an Ethernet network to plug the player into.

Best Blu-ray Movie Deals