A2-300 Custom Glass....

[aramis109]

Looks really good. Personally I would've made the glass to match the bezel of the sub (IE made it a little smaller). Minor quibble though. I'll be interested to see the final product.

[repete66211]

Originally Posted by Therapist

Put this in this forum to get the most feedback. I have a project in mind for my A2-300. I want to get a piece of Very Dark Glass cut precisely to fit the top of the sub. 1/4 inch thick and very dark with little clear rubber feet under it to prevent it from rattling . NOW the part where you guys come in is I think I'm gonna have "elemental designs™" etched/sandblasted into the surface and need to know which way you think it would look best. And feel to post and tell me if you think its a dumb idea too.

I'm wondering if it should be left to right dead center.... vertical, bottom to top....along one side left or right vertical. WHERE should I put it? Let me know! .....or perhaps angles form one corner to another?

I'm leaning towards putting it either dead center left to right or along the left side front to back or maybe corner to corner........Help me decide..

Not that it'll come into play or anything, but their logo has copyright protection. Technically anyone who etches that, especially if reaping commercial benefit, is probably violating copyright law. (I found this out when I tried to get a logo tattoo.) But, like I said, probably no big deal. You could always write for permission.

[Tru2theBlu]

Originally Posted by BrettBell_eD_Rep

That does look so cool!!! I can't wait to see the logo as well.

Brett thought it was cool, ED must not care?

[repete66211]

Originally Posted by Tru2theBlu

Brett thought it was cool, ED must not care?

OP: Disregard my previous post.

[Driver_King]

Originally Posted by Tru2theBlu

Brett thought it was cool, ED must not care?

I hope not! It would go on top of the subwoofer anyways and makes it look even better. Seriously though, if this is the case, then all the people with name brand plaques that say "this theater features" and then has all sorts of brands like Polk, Pioneer, ect. are screwed. Better look out for those logo enforcing people out to get you.

[Tru2theBlu]

Originally Posted by Driver_King

I hope not! It would go on top of the subwoofer anyways and makes it look even better. Seriously though, if this is the case, then all the people with name brand plaques that say "this theater features" and then has all sorts of brands like Polk, Pioneer, ect. are screwed. Better look out for those logo enforcing people out to get you.

Orwell was right!

[naturephoto1]

Originally Posted by Tru2theBlu

Orwell was right!

But, it is way passed 1984.

Rich

[Tru2theBlu]

Originally Posted by naturephoto1

But, it is way passed 1984.

Rich

Yes sir.

[repete66211]

Originally Posted by Driver_King

I hope not! It would go on top of the subwoofer anyways and makes it look even better. Seriously though, if this is the case, then all the people with name brand plaques that say "this theater features" and then has all sorts of brands like Polk, Pioneer, ect. are screwed. Better look out for those logo enforcing people out to get you.

I suppose there's little threat of litigation. After all, it's not a Monster logo.

[Therapist]

onedayglass.com their place is located about 10 miles form my house so i didnt have to pay shipping.

[SDBlu]

Originally Posted by Therapist

Well my buddy hooked me up with this glass shop with one day turnaround. Apple tv on top for now. Still looking for a place to do etching. ZERO rattle using blue sticky poster stuff for spacing.

Therapist, I think your idea for the glass-top was great. I think it looks good too

What is this blue-sticky poster stuff you are using to put under the glass??? And are you sure there is no rattle? Have you demoed some bass-heavy tracks at louder volumes?

[Therapist]

http://www.amazon.com/Darice-Dap-Fun-Tak-Reusable-Adhesive/dp/B0001DSDBE

ZERO rattle. The glass is raised approximately 3/16 inch off the sub no contact whatsoever.

[SDBlu]

Originally Posted by Therapist

http://www.amazon.com/Darice-Dap-Fun-Tak-Reusable-Adhesive/dp/B0001DSDBE

ZERO rattle. The glass is raised approximately 3/16 inch off the sub no contact whatsoever.

cool, thanks.

[JasonR]

Originally Posted by Therapist

Well my buddy hooked me up with this glass shop with one day turnaround. Apple tv on top for now. Still looking for a place to do etching. ZERO rattle using blue sticky poster stuff for spacing.

Fantastic! I am glad it worked out! Can't wait to see the finished product!

[Therapist]

Well my riser showed up (GRAMMA) and it definitely tightened up the bass and hopefully made it so it doesn't rattle my downstairs neighbors possessions as much . Will post pictures of everything as soon as my missing parts for my omnimount G3FP arrive this week.

[DavidAg02]

Originally Posted by Therapist

Well my riser showed up (GRAMMA) and it definitely tightened up the bass and hopefully made it so it doesn't rattle my downstairs neighbors possessions as much . Will post pictures of everything as soon as my missing parts for my omnimount G3FP arrive this week.

The gramma is a great product. Glad you are enjoying it.

[Driver_King]

Originally Posted by Therapist

Well my riser showed up (GRAMMA) and it definitely tightened up the bass and hopefully made it so it doesn't rattle my downstairs neighbors possessions as much . Will post pictures of everything as soon as my missing parts for my omnimount G3FP arrive this week.

Pics.

[Therapist]

thanks for the reminder. I just uploaded some new photos. Still need to put up drapes and framed movie posters, and do a little wire management just to the right of the sub. And a wood wedge to angle my sub upward a little bit. I'm also thinking of trying some different places for the apple tv but we will see.

[Driver_King]

Did you get the glass etched yet?

[Therapist]

not yet. still shopping local places who can do it.